|
|
 |
| Stage
One |
| Sediment Filter, 5-Micron
Polyspun Cartridge, 2 1/2” dia. x 9 3/4" long |
|
Stage
two |
Activated Carbon Block
Filter
5 Micron, 2 1/2” dia. x 9 3/4" long |
|
| Stage
Three |
| Reverse Osmosis Membrane,
Filmtec 36 GPD TFC @ 65 PSI Pressure Differential |
|
| Stage
Four |
Post-Filter, In-Line,
Granular
Activated Carbon, 2” dia. x 10” long |
|
| Tank |
| 4.0 Gallon Plastic Tank
(metal tank available), Pre-pressurized with Butyl Bladder,
2.5 gal. water capacity |
| Certified
Reduced Contaminants |
Arsenic
Barium
Cadmium
Chromium III & VI
Copper
Lead
Nitrate
|
Nitrite
Selenium
Radium 226 & 228
Fluoride
Turbidity
Cysts
TDS |
Tested for structural integrity,
chemical extraction and reduction of contaminants
View
NSF/ANSI-58 |
2 Year Limited Warranty
|
Use this system when the water
pressure is below 40-psi. This happens in many towns and villages,
and also with well water systems. The booster pump allows
the system to run at peak efficiency by providing a pressure
of 80psi to the RO membrane.The pump is placed after the first
stage sediment filter to reduce wear from sediment. The pump
motor operates at 24volts D.C. and is supplied with a step-down
transformer which plugs into a standard 110-volt outlet (220
volt available). A pressure switch is located on the line
to the storage tank which turns the pump OFF when the tank
pressure is 40-psi and ON at 25-psi.
An AUTOFLUSH version is also available. Autoflush prolongs
the life of the RO membrane, especially in areas with high
TDS, sediment load and hardness. Each time the pump turns
on, the autoflush valve opens to permit full flow to the drain
for 20-seconds, flushing the inside of the membrane of any
built up contaminants. This reduces plugging of the membrane
and ensures efficient rejection of TDS for a longer period
of time. RECOMMENDED FOR WATER OVER 500 TDS.
|
|
|
Download
a Brochure. For
other Models, Click Here.
|
| Features |
•
•
•
•
•
•
|
Auto Shut-off
valve (conserves water)
Flow Restrictor – modified capillary
Long Reach, Non-airgap Faucet
Feed water connector – Threaded Inlet Adapter with Metal
Ballvalve
Drain Clamp
1/4 Inch Flexible Polyethylene Tubing w/JACO Compression Fittings
|
| Specifications
Shipping Weight: 32 lb.
Dimension: 15”L x 7”W x 15 1/2”H
Tank: 11 dia. x 15 1⁄2”H
Booster Pump: 110/24V DC transformer |
Conditions of Use
• Water Must be microbiologically
safe
• Temperature, 40 -100 degrees F
• pH Range, 3 to 11
• Feed pressure, 20 to 100 psig
• Maximum TDS, 1500 PPM
• Turbidity, less than 1.0 NTU
|
|
|
AVAILABLE OPTIONS
4 stage Reverse Osmosis
Autoflush option
Air Gap Faucet option
3/8" Line to Faucet option
Self-piercing Saddle Valve option
Quick Connect Fittings option
Metal Tank option
Filter Replacement Kit
|
PT-4.0/P
add /AF
add /AG
add /3/8
add /SV
add /QC
add /MT
FK-100
|
|
